High Lifter 2024 Polaris RZR XP 1000 APEXX Front Forward Arms
All new High Lifter APEXX Control Arms are stronger, adjustable and engineered for the most punishing terrain with 1.75" of additional ground clearance and raked forward 1.5". Push your Polaris RZR to the limits and tackle obstacles you couldn't before! Optional preinstalled ball joints.
Heavy Duty Strength
High Lifter's new heavy duty control arms add more support than factory. Our upper and lower arms are made with the same material for added strength, so they can withstand the abuse applied during a typical ride. High Lifter arms are constructed out of 1.5" DOM with .188 wall tubing. This is a 50% increase in size and a 70% increase in steel thickness for added durability and strength.
Built in Adjustability
The lower arms also feature an adjustability component in the bushing collars to eliminate premature wearing that can come from the addition of lift kits, portals, or larger tires. When the kit is set to the factory position, you have 3/8" of adjustability camber in and out. Heat treated and plated adjustable bushing collars allow you to be confident in the strength you're adding to your ride. This kit comes packaged and preadjusted to the factory position, and factory bushings and caps should be used for installation.
Increased Ground Clearance
We maximized ground clearance by strategically arching the lower control arm with double and TRIPLE bends. This unique design allowed us to get an additional 1.75" of ground clearance to avoid impacting those nasty trail obstacles. These bends maintain the factory geometry, which helps reduce wear on components like axles and tie rods. Our forward arms allow you to run larger tires without a suspension lift. We've improved the upper control arm by repositioning the sway bar tab. This will reduce the extreme angles places on the sway bar links and reduce wear.
Reinforced Ball Joints Brackets
Portals and large tires apply torque that can distort the ball joint bracket, leading to failure of the arms. With over 130% increase in the ball joint mounting area, we are helping to prevent breakdown or "egging" of the mounting bracket.
Tire Fitment: Up to 34.5"
Our tire fitment guide is a general fitment and is in no way guaranteed. Tires and lifts vary by manufacture and tire fitment can be affected by other modifications such as, but not limited to, wheel offset, actual tire diameter and actual tire width. Always verify your brand of tires, lift, and other modifications prior to making a buying decision.
Optional Preinstalled Ball Joints
High Lifter's service team uses a hydraulic press to install the ball joint with the correct pressure and alignment, also making sure the clip is fully seated and secured. Purchasing control arms with the ball joints already installed adds to easy installation and prevents damage due to improper installation, which is not covered by High Lifter's Lifetime Warranty.
Features
- Adjustable heat-treated collars for camber adjustability with a 1" thread
- Raked forward 1.5"
- Over 3 degrees of camber adjustment in each direction
- Heavy duty ball joint brackets to eliminate deformation issues, Keller ball joint compatible
- Ladder bar compatible with the 1.5" ID clamps
- Extreme duty 1.5" x .120" DOM steel construction
- Up to 2" of added ground clearance compared to OEM lower arm
- Mounting accommodations for OEM brake lines using OEM tabs instead of P-clamps
- Optimized sway bar linkage angles
- Limited Lifetime Warranty (Excludes wearable items like bushings, bearings, cones, and heim joints)
- Powder Coated
Fitment
- 2025 Polaris RZR XP 1000 Premium
- 2025 Polaris RZR XP 1000 Sport
- 2025 Polaris RZR XP 1000 Ultimate
- 2025 Polaris RZR XP 4 1000 Premium
- 2025 Polaris RZR XP 4 1000 Sport
- 2025 Polaris RZR XP 4 1000 Ultimate
- 2024 Polaris RZR XP 1000 Premium
- 2024 Polaris RZR XP 1000 Sport
- 2024 Polaris RZR XP 1000 Ultimate
- 2024 Polaris RZR XP 4 1000 Premium
- 2024 Polaris RZR XP 4 1000 Sport
- 2024 Polaris RZR XP 4 1000 Ultimate
Notes
- Control arms with preinstalled APEXX Ball Joints will still need to be adjusted to spec once installed on the machine. The APEXX Ball Joints do not come preset.
- APEXX Ball Joints should be re-adjusted after every ride to prevent abnormal or premature wear.
High Lifter (About)
High Lifter Products, has been developing and marketing unique, after-market accessories for utility, 4-wheel drive ATVs, UTVs, and RUVs since 1996. In this short time, the company has grown from a one-man, backyard hobby into a 85 employee, multi-million dollar corporation.
Business operations are carried out at our 52,000 square foot location in Shreveport, Louisiana. This building includes a retail showroom, a manufacturing and fabrication facility, a performance shop, executive offices, and is surrounded by 3 large warehouses. We also operate through our main website, www.highlifter.com, which is visited by millions of unique visitors each year, and includes a full product listing, a forum and more information on our annual Mud National Events.
